Search Results

This paper describes experiments conducted to determine Federal Test Procedure (FTP) exhaust emissions, ozone-forming potentials, specific reactivities, and reactivity adjustment factors for several butane/propane alternative fuel blends run on a light-duty EHC-equipped gasoline vehicle converted to operate on liquefied petroleum gas (LPG). Duplicate emission tests were conducted on the light-duty vehicle at each test condition using appropriate EPA FTP test protocol. Hydrocarbon speciation was utilized to determine reactivity-adjusted non-methane organic gas (NMOG) emissions for one test on each fuel.

Only a limited understanding of the oil consumption mechanism appears to exist, especially oil consumption under transient engine operating conditions. This is probably due to the difficulty in engine instrumentation for measuring not only oil consumption, but also for measuring the associated in-cylinder variables. Because of this difficulty, a relatively large number of experiments and tests are often necessary for the development of each engine design in order to achieve the target oil consumption that meets the requirements for particulate emissions standards, oil economy, and engine reliability and durability. Increased understanding and logical approaches are believed to be necessary in developing the oil-consumption reduction technology that effectively and efficiently accomplishes the tasks of low oil-consumption engine development.

An Emergency Tire Inflation System (ETIS) designed for use on commercial trucks was evaluated and tested. The ETIS is provided in kit form and designed to be installed by a truck operator to provide emergency air to inflate a low or punctured tire on tractor drive axles. The ETIS will continue to supply air to the tire until the system pressure falls below a safe air pressure level. The system is designed to allow the rig to be driven 500 miles to a tire repair station or to a safe location where tire repair service is available. The installation kit (Figure 1), which can fit under a truck seat, includes all the necessary equipment to install the system on the most common drive axles. The ETIS supplies air to the under-inflated tire through a previously qualified1 Rotary Union design. The Rotary Union is attached to the axle flange of the drive axle by a threaded adapter and two adjustable links that allow the Rotary Union to be placed at the center of rotation of the axle.

An Automatic Tire Inflation System (ATIS), specifically designed for use on commercial long haul trailers, requires modification of the axles to direct air to the tires. The ATIS requires a drilled hole through the axle tube for the installation of a pneumatic fitting. The trucking industry expressed concern about the modification and its impact upon the axle structure, and the general durability of the system over a long period. A three-phase test program was developed and conducted to satisfy the concerns of the industry.

This paper presents a discussion on manual transmission torque losses and focuses specifically on the relationship between torque loss, input speed and torque. It also includes a discussion on other factors affecting torque loss, such as inclination angle and lube oil temperature. Manual transmissions used in compact light truck applications have torque losses that are a function of input speed and torque. Efficiency studies done on manual transmissions in the engine-driving mode indicate that torque losses, in other than direct-drive gears, are considerably more dependent on input torque than input speed. It was also observed that efficiency was significantly affected by the inclination angle and lube oil temperature.

A non-thermal plasma treatment of diesel engine exhaust was effective in removing particulate (soot) and oxides of nitrogen (NOx) from two different light-duty diesel vehicles: an older-technology indirect-injection Toyota truck, and a newer-technology direct-injection Dodge truck. Particulate removal efficiencies and NOx conversion efficiencies were determined at space velocities up to 20,000/hr. Particulate removal efficiencies were above 60 percent for most conditions, but decreased with increasing space velocities. Conversion efficiencies for NOx and carbon monoxide (CO) were also dependent on the space velocity. The NOx conversion efficiencies were generally greater than 40 percent at space velocities less than 7000/hr. The CO concentration increased through the plasma reaction bed indicating that CO was produced by reactions in the plasma.

Development of methodology for diesel hydrocarbon speciation of C12-C22 compounds and the application of that methodology to determine total ozone forming potential of diesel exhaust emissions is an extremely complicated task. Methodology has already been developed for speciating C1-C12 exhaust emissions from engines and vehicles fueled with gasoline, diesel, and alternate fuels. However, very little or no information is available for exhaust speciation of C12-C22 compounds as sampling and analytical constraints make the collection and analysis of the higher molecular weight compounds extremely challenging. Key issues related to the definition of “hydrocarbons” also need to be addressed prior to promulgation of future reactivity-based legislation for diesels (e.g., Which exhaust hydrocarbon compounds actually exist in gas-phase and participate in atmospheric ozone formation?).

Southwest Research Institute (SwRI) converted two small air-cooled, gasoline engines to operate on LPG (sometimes called propane since propane is LPG's major constituent). Typical two- and four-cycle engines were chosen for this investigation. The two-cycle engine used was a McCulloch string trimmer engine with 28 cc displacement. The four-cycle engine used was an L-head, Tecumseh TVS90 with 148 cc displacement. These are typical of engines found on lower cost lawn mowers and string trimmers. The engines were baseline tested on gasoline, converted to LPG, and tested to determine equivalence ratios at which the engines could be operated without exceeding manufacturers' recommended spark plug seat or exhaust temperatures. Engine startability and throttle response was maintained with the LPG conversion. The emissions of the four-cycle engine were measured following the CARB 6-mode emissions test procedure.

Recent legislation, including the California Clean Air Act of 1988 and the Federal Clean Air Act Amendment of 1990, includes off-road engines, equipment, and vehicles as targets for new exhaust emissions regulations. The Santa Barbara County Air Pollution Control District in cooperation with EXXON USA is conducting a major Low NOx Demonstration Program including mobile sources, construction equipment, and offshore equipment. As a part of this program, an existing backhoe has been retrofitted with a low NOx engine and demonstrated in the field. This paper discusses the work performed to allow Case model 580 backhoes to be retrofitted with Cummins 4BTAA3.9 on-highway turbocharged diesel engines. A standard production conversion kit can be used to mount the new engines in place of the older existing JI Case engines in some models while other newer models already have 4B3.9 engines. In addition, an air-to-air aftercooler and associated plumbing was designed and installed.

Emissions from existing diesel-powered urban buses are increasingly scrutinized as local, state, and federal governments require enforcement of more stringent emission regulations and expectations. Currently, visual observation of high smoke levels from diesel-powered equipment is a popular indicator of potential emission problems requiring tune-up or engine maintenance. It is important that bus inspection and maintenance (I/M) operations have a quality control “test” to check engine emissions or diagnose the engine state-of-tune before or after maintenance. Ideally, the “emission test” would be correlated to EPA transient emissions standards, be of short duration, and be compatible with garage procedures and equipment. In support of developing a useful “short-test,” equipment was designed to collect samples of raw exhaust over a short time period for gaseous and particulate emissions.

Small engines which are friendly toward the environment are needed all over the world, whether the need is expressed in terms of energy efficiency, useful engine life, health benefits for the user, or emission regulations enacted to protect a population or an ecologically-sensitive area. Progress toward the widespread application of lower-impact small engines is being made through engine design, matching of engine to equipment and task, aftertreatment technology, alternative and reformulated fuels, and improved lubricants. This paper describes three research and development projects, focused on the interrelationships of fuels, lubricants, and emissions in Otto-cycle engines, which were conducted by Southwest Research Institute. All the work reported was funded internally as part of a commitment to advance the state of small engine technology and thus enhance human utility.

Recent approval of emission standards for small utility engines by the California Air Resources Board(1)* suggests that substantial reductions in emissions from small utility engines will soon be required. While 1994 standards may be met with simple engine adjustments or modifications, 1999 standards are much more stringent and may require the use of catalysts in conjunction with other emission reduction technologies. Assessing the feasibility of candidate emission control strategies is an important first step. Various emission reduction technologies were applied to three different 4-stroke engines. Emission tests were conducted to determine the effectiveness of air/fuel ratio changes, thermal oxidation, exhaust gas recirculation, and catalytic oxidation with and without supplemental air. Results of these evaluations, along with implications for further work, are presented. One engine's emissions were reduced below the levels of 1999 ARB standards.

Antilock brake systems for air braked vehicles have been growing in popularity in Great Britain and Europe and appear to be candidates for extensive use in the United States as well. Previous mandated use in the United States during the 1970's was not successful, in part because of reliability problems, and the National Highway Traffic Safety Administration (NHTSA) has decided that a thorough evaluation of air brake antilock systems is necessary prior to any decision about the appropriateness of future mandatory use in the United States. This paper describes the electronic data collection equipment and processing techniques which are being used in the NHTSA 200 truck evaluation project. Detailed maintenance histories for each truck are being recorded manually as a separate segment of the project. An average of 6 to 7 megabytes of data per week is being collected in the various cities in which fleets are operating test vehicles.

Measurement of emissions from small utility engines has usually been accomplished using steady-state raw emissions procedures such as SAE Recommended Practice J1088. While raw exhaust measurements have the advantage of producing modal exhaust gas concentration data for design feedback; they are laborious, may influence both engine performance and the emissions themselves, and have no provision for concurrent particulate measurements. It is time to consider a full-dilution procedure similar in principle to automotive and heavy-duty on-highway emission measurement practice, leading to improvements in many of the areas noted above, and generally to much higher confidence in data obtained. When certification and audit of small engine emissions become a reality, a brief dilute exhaust procedure generating only the necessary data will be a tremendous advantage to both manufacturers and regulatory agencies.

The Toyota lean combustion system-methanol (T-LCS-M) is a lean burn methanol combustion system designed to maximize fuel economy and driving performance while minimizing pollutant emissions. Testing at the EPA Motor Vehicle Emissions Laboratory (MVEL) indicates that this system allows relatively low emissions of regulated pollutants and aldehydes when operated on either M100 or M85 methanol fuels under transient driving and evaporative emissions test conditions. Total vehicle hydrocarbon emissions appear lower when the vehicle is operated on M100 rather than M85 fuel. Fuel economy is slightly improved when the system is operated on M85 rather than M100 fuel.

Regulated gaseous, particulate and several unregulated emissions are reported from four heavy-duty diesel engines operated on the chassis version of the 1983 transient procedure. Emissions were obtained from Caterpillar 3208, Mack ENDT 676, Cummins Formula 290 and Detroit Diesel 8V-71 engines with several diesel fuels. A large dilution tunnel (57′ × 46″ ID) was fabricated to allow total exhaust dilution, rather than the double dilution employed in the stationary engine version of the transient procedure. A modal particulate sampler was developed to obtain particulate data from the individual segments of the 1983 transient procedure. The exhaust gas was analyzed for benzo(a)pyrene, metals, N2O, NO2, individual hydrocarbons and HCN. Sequential extractions were performed and measured versus calculated fuel consumptions were obtained.

Five light-duty vehicles were used to investigate HC, CO, and NOx emissions and fuel economy sensitivity to changes in the length of soak period preceding the EPA Urban Dynamometer Driving Schedule (UDDS). Emission tests were conducted following soak periods 10 minutes to 36 hours in length. Each of the first 8 minutes of the driving cycle was studied separately to observe vehicle warm-up. Several engine and fuel system temperatures were monitored during soak and run periods and example trends are illustrated. The extent to which emission rates and fuel consumption are affected by soak period length is discussed.

The research program on which this paper is based included both laboratory emission measurements and extrapolation of results to the national population of heavy-duty farm, construction, and industrial engines. Emission tests were made on four gasoline engines and eight diesel engines typical of those used in F, C, and I equipment. Gaseous and particulate emissions were measured during engine operation on well-accepted steady-state procedures, and diesel smoke was measured during both steady-state conditions and the Federal smoke test cycle. Emissions measured were hydrocarbons, CO, CO2, NO, NOx, O2, aliphatic aldehydes, light hydrocarbons, particulate, and smoke. Emission of sulfur oxides (SOx) was estimated on the basis of fuel consumed, and both evaporative and blowby hydrocarbons were also estimated where applicable (gasoline engines only). Data on emissions obtained from this study were compared with those available in the literature, where possible.

This paper summarizes an investigation of reductions in exhaust emission levels attainable using various techniques appropriate to gasoline engines used in vehicles over 14,000 lbs GVW. Of the eight gasoline engines investigated, two were evaluated parametrically resulting in an oxidation and reduction catalyst “best combination” configuration. Four of the engines were evaluated in an EGR plus oxidation catalyst configuration, and two involved only baseline tests. Test procedures used in evaluating the six “best combination” configurations include: three engine emission test procedures using an engine dynamometer, a determination of vehicle driveability, and two vehicle emission test procedures using a chassis dynamometer. Dramatic reductions in emissions were attained with the catalyst “best combination” configurations. Engine durability, however, was not investigated.

This is a summary compilation and analysis of exhaust-emission results and operating parameters from forty-five heavy-duty gasoline and diesel-powered vehicles tested over a 7.24-mile road course known as the San Antonio Road Route (SARR); and, for correlative purposes, on a chassis dynamometer.(2) Exhaust samples were collected and analyzed using the Constant Volume Sampler (CVS) technique similar to that used in emission testing of light-duty vehicles. On the road course, all equipment and instrumentation were located on the vehicle while electrical power was supplied by a trailer-mounted generator. In addition to exhaust emissions, operating parameters such as vehicle speed, engine speed, manifold vacuum, and transmission gear were simultaneously measured and recorded on magnetic tape. The forty-five vehicles tested represent various model years, GVW ratings, and engine types and sizes.